web analytics

100% Pass Ensure 200-601 Dumps with Free VCE and PDF (Question 21 – Question 25)

New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ

QUESTION 21
A ProfiNET management system operator is unable to see diagnostic information for a Cisco Industrial Ethernet switch that has been added to a SIMATIC management station. Based on the provided CLI output, which statement is correct?
switch# show profinet status
State : Enabled
Vlan : 201
Id : IE2000-Switch
Connected : Yes
ReductRatio : 128
GSD version : Mis-match

A.    The assigned ProfiNET VLAN is not valid and should be less than 100
B.    LLDP has been disabled on this switch
C.    The GSD file version on the switch does not match the GSD file version on the management station
D.    The Reduction Ration has been set too low

Answer: C

QUESTION 22
What can be done to increase the security in depth in an industrial zone?

A.    Add additional disk storage to the IDS server
B.    Add specific SCADA signatures to the IDS server
C.    Create a high availability solution for the IDS server
D.    Place a ‘data diode’ in front of the IDS server

Answer: B

QUESTION 23
Your supervisor calls you and tells you that one of the Stratix 5700 switches is not assigning all CIP explicit messages to the proper QoS queue. The switch was deployed with the ab-global macro and CIP explicit messages were previously being assigned to the proper QoS queue. You suspect the access-lists associated with the ab-global macro have been changed. Look at the following access list from the switch configuration:
access-list 101 permit udp any eq 2222 any dscp 55
access-list 102 permit udp any eq 2222 any dscp 47
access-list 103 permit udp any eq 2222 any dscp 43
access-list 104 permit udp any eq 2222 any
access-list 105 permit udp any eq 44818 any
access-list 105 permit tcp any eq 44816 any
What needs to be done to fix the above access list?

A.    Access list 105 should reference udp port 44816
B.    Access lists 101-104 should reference udp port 2212
C.    Access list 105 should reference tcp port 44818
D.    Access list 104 should be a deny access list rather than a permit access list

Answer: C

QUESTION 24
What should be done with unused conductors in copper unshielded or shielded twisted-pair network cables?

A.    terminate in their characteristic impedance
B.    trim back and properly insulate
C.    connect to protective earth
D.    splice to a used conductor

Answer: A

QUESTION 25
Cisco Industrial Ethernet switches are capable of sending alarm messages to ProfiNET management stations using the ProfiNET-IO protocol. Which four are alarms that can be configured for an interface? (Choose four.)

A.    Port Not Forwarding
B.    Port Not Operating
C.    Port LLDP Disabled
D.    Port QoS Disabled
E.    Port Duplex Mismatch
F.    Port FCS Errors Exceeded Threshold
G.    Port CRC Errors Exceeded Threshold
H.    Port Link Fault

Answer: ABFH


New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ