web analytics

Cisco CCNA 200-105 Dumps With VCE and PDF Download (Question 141 – Question 150)

New 200-105 exam questions from PassLeader 200-105 dumps! Welcome to download the newest PassLeader 200-105 VCE and PDF dumps: http://www.passleader.com/200-105.html (346 Q&As)

P.S. Free 200-105 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpUTVNc3otMV8xMkU

QUESTION 141
What is a valid HSRP virtual MAC address?

A.    0000.5E00.01A3
B.    0007.B400.AE01
C.    0000.0C07.AC15
D.    0007.5E00.B301

Answer: C
Explanation:
Hot Standby Router Protocol Features and Functionality
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a91.shtml
HSRP Addressing
In most cases when you configure routers to be part of an HSRP group, they listen for the HSRP MAC address for that group as well as their own burned-in MAC address. The exception is routers whose Ethernet controllers only recognize a single MAC address (for example, the Lance controller on the Cisco 2500 and Cisco 4500 routers). These routers use the HSRP MAC address when they are the Active router, and their burned-in address when they are not.
HSRP uses the following MAC address on all media except Token Ring:
0000.0c07.ac** (where ** is the HSRP group number)

QUESTION 142
Lab Simulation Question – EIGRP
passleader-200-105-dumps-1421

Answer:
First we should check the configuration of the ENG Router.
Click the console PC ā€œFā€ and enter the following commands.
ENG> enable
Password: cisco
ENG# show running-config
Building configuration…
Current configuration : 770 bytes
!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname ENG
!
enable secret 5 $1$mERr$hx5rVt7rPNoS4wqbXKX7m0
!
interface FastEthernet0/0
ip address 192.168.77.34 255.255.255.252
duplex auto
speed auto
!
interface FastEthernet0/1
ip address 192.168.60.65 255.255.255.240
duplex auto
speed auto
!
interface FastEthernet1/0
ip address 192.168.60.81 255.255.255.240
duplex auto
speed auto
!
router eigrp 22
network 192.168.77.0
network 192.168.60.0
no auto-summary
!
ip classless
!
line con 0
line vty 0 4
login
!
end
ENG#
From the output above, we know that this router was wrongly configured with an autonomous number (AS) of 22. When the AS numbers among routers are mismatched, no adjacency is formed.
(You should check the AS numbers on other routers for sure)
To solve this problem, we simply re-configure router ENG router with the following commands:
ENG# conf t
ENG(config)# no router eigrp 22
ENG(config)# router eigrp 222
ENG(config-router)# network 192.168.60.0
ENG(config-router)# network 192.168.77.0
ENG(config-router)# no auto-summary
ENG(config-router)# end
ENG# copy running-config startup-config
Second we should check the configuration of the MGT Router.
Click the console PC ā€œGā€ and enter the following commands.
MGT> enable
Password: cisco
MGT# show running-config
Building configuration…
Current configuration : 1029 bytes
!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname MGT
!
enable secret 5 $1$mERr$hx5rVt7rPNoS4wqbXKX7m0
!
interface FastEthernet0/0
ip address 192.168.77.33 255.255.255.252
duplex auto
speed auto
!
interface Serial0/0
ip address 192.168.36.13 255.255.255.252
clock rate 64000
!
interface Serial0/1
ip address 192.168.60.25 255.255.255.252
clock rate 64000
!
interface Serial1/0
ip address 198.0.18.6 255.255.255.252
!
interface Serial1/1
no ip address
shutdown
!
interface Serial1/2
no ip address
shutdown
!
interface Serial1/3
no ip address
shutdown
!
router eigrp 222
network 192.168.36.0
network 192.168.60.0
network 192.168.85.0
network 198.0.18.0
no auto-summary
!
ip classless
ip route 0.0.0.0 0.0.0.0 198.0.18.5
!
line con 0
line vty 0 4
login
!
end
MGT#
Notice that it is missing a definition to the network ENG. Therefore we have to add it so that it can recognize ENG router
MGT# conf t
MGT(config)# router eigrp 222
MGT(config-router)# network 192.168.77.0
MGT(config-router)# end
MGT# copy running-config startup-config
Now the whole network will work well. You should check again with ping command from router ENG to other routers!
In Short:
ENG Router
ENG>enable
Password: cisco ENG# conf t
ENG(config)# no router eigrp 22
ENG(config)# router eigrp 222
ENG(config-router)# network 192.168.60.0
ENG(config-router)# network 192.168.77.0
ENG(config-router)# no auto-summary
ENG(config-router)# end
ENG# copy running-config startup-config
MGT Router
MGT>enable
Password: cisco MGT# conf t
MGT(config)# router eigrp 222
MGT(config-router)# network 192.168.77.0
MGT(config-router)# end
MGT# copy running-config startup-config
Some Modification in Question
After adding ENG router, no routing updates are being exchanged between MGT and the new location. All other inter connectivity for the existing locations of the company are working properly. But Internet connection for existing location including Remote1 and Remote2 networks are not working.
Faults Identified:
1. Incorrect Autonomous System Number configured in ENG router.
2. MGT router does not advertise route to the new router ENG.
3. Internet Connection is not working all stations.
We need to correct the above two configuration mistakes to have full connectivity
Steps:
1. ENG Router: Change the Autonomous System Number of ENG
2. Perimiter Router: Add the network address of interface of Permiter that link between MGT and ENG.
3. Perimiter Router: Add default route and default-network.
Check the IP Address of S1/0 interface of MGT Router using show running-config command. (The interfaced used to connect to the ISP)
!
interface Serial1/0
ip address 198.0.18.6 255.255.255.252
!
For Internet sharing we have create a default route, and add default-network configuration. The IP address is 198.0.18.6/30. Then the next hop IP will be 198.0.18.5.
ENG Router
ENG>enable
Password: cisco ENG# conf t
ENG(config)# no router eigrp 22
ENG(config)# router eigrp 222
ENG(config-router)# network 192.168.60.0
ENG(config-router)# network 192.168.77.0
ENG(config-router)# no auto-summary
ENG(config-router)# end
ENG# copy running-config startup-config
MGT Router
MGT>enable
Password: cisco MGT# conf t
MGT(config)# router eigrp 222
MGT(config-router)# network 192.168.77.0
MGT(config-router)# exit
MGT(config)# ip route 0.0.0.0 0.0.0.0 198.0.18.5
MGT(config)# ip default-network 198.0.18.0
MGT(config)# exit
MGT# copy running-config startup-config
Important:
If you refer the topology and IP chart, the MGT router uses Fa0/0 to connect ENG router, S0/0 used to connect Remote1, and S0/1 used to connect Remote2.
Refer to the command show running-config, the command #PASSIVE-INTERFACE <Interface Name> will deny EIGRP updates to specified interface. In that case we need to use #no passive-interface <Interface Name> to allow the routing updates to be passed to that interface. For example when used the #show run command and we see the output like below.
!
router eigrp 22
network 192.168.77.0
network 192.168.60.0
passive-interface FastEthernet 0/0
passive-interface Serial 1/0
no auto-summary
!
Then the command would be
MGT(config)#router eigrp 222
MGT(config-router)#no passive-interface Fa0/0
MGT(config-router)#end
Also MGT router connect to the ISP router using Serial 1/0. If you seen passive-interface s1/0, then do not remove it using #no passive-interface s1/0 command.

QUESTION 143
Refer to the exhibit. How should the FastEthernet0/1 ports on the 2950 model switches that are shown in the exhibit be configured to allow connectivity between all devices?
passleader-200-105-dumps-1431

A.    The ports only need to be connected by a crossover cable
B.    SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk
C.    SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode access
SwitchX(config-if)# switchport access vlan 1
D.    SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk
SwitchX(config-if)# switchport trunk vlan 1
SwitchX(config-if)# switchport trunk vlan 10
SwitchX(config-if)# switchport trunk vlan 20

Answer: B

QUESTION 144
Refer to the exhibit. A junior network engineer has prepared the exhibited configuration file. What two statements are true of the planned configuration for interface fa0/1? (Choose two.)
passleader-200-105-dumps-1441

A.    The two FastEthernet interfaces will require NAT configured on two outside serial interfaces.
B.    Address translation on fa0/1 is not required for DMZ Devices to access the Internet.
C.    The fa0/1 IP address overlaps with the space used by s0/0.
D.    The fa0/1 IP address is invalid for the IP subnet on which it resides.
E.    Internet hosts may not initiate connections to DMZ Devices through the configuration that is shown.

Answer: BE

QUESTION 145
Refer to the exhibit.
Which statement describes DLCI 17?
passleader-200-105-dumps-1451

A.    DLCI 17 describes the ISDN circuit between R2 and R3.
B.    DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.
C.    DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D.    DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.

Answer: C
Explanation:
DLCI stands for Data Link Connection Identifier. DLCI values are used on Frame Relay interfaces to distinguish between different virtual circuits. DLCIs have local significance because, the identifier references the point between the local router and the local Frame Relay switch to which the DLCI is connected.

QUESTION 146
What is the default Local Management Interface frame type transmitted by a Cisco router on a Frame Relay circuit?

A.    Q933a
B.    B8ZS
C.    IETF
D.    Cisco
E.    ANSI

Answer: D

QUESTION 147
Refer to the exhibit. The network shown in the exhibit has just been installed. Host B can access the Internet, but it is unable to ping host C. What is the problem with this configuration?
passleader-200-105-dumps-1471

A.    Host B should be in VLAN 13.
B.    The address of host C is incorrect.
C.    The gateway for host B is in a different subnet than the host is on.
D.    The switch port that sends VLAN 13 frames from the switch to the router is shut down.
E.    The switch port connected to the router is incorrectly configured as an access port.

Answer: B

QUESTION 148
Which protocol provides a method of sharing VLAN configuration information between switches?

A.    VTP
B.    STP
C.    ISL
D.    802.1Q
E.    VLSM

Answer: A
Explanation:
Understanding VLAN Trunk Protocol (VTP)
http://www.cisco.com/en/US/tech/tk389/tk689/technologies_tech_note09186a0080094c52.shtml
Introduction
VLAN Trunk Protocol (VTP) reduces administration in a switched network. When you configure a new VLAN on one VTP server, the VLAN is distributed through all switches in the domain. This reduces the need to configure the same VLAN everywhere. VTP is a Cisco-proprietary protocol that is available on most of the Cisco Catalyst series products.

QUESTION 149
Refer to the exhibit. What is the most appropriate summarization for these routes?
passleader-200-105-dumps-1491
A.    10.0.0.0 /21
B.    10.0.0.0 /22
C.    10.0.0.0 /23
D.    10.0.0.0 /24

Answer: B

QUESTION 150
The network administrator has been asked to give reasons for moving from IPv4 to IPv6. What are two valid reasons for adopting IPv6 over IPv4? (Choose two.)

A.    no broadcast
B.    change of source address in the IPv6 header
C.    change of destination address in the IPv6 header
D.    Telnet access does not require a password
E.    autoconfiguration
F.    NAT

Answer: AE
Explanation:
Six Benefits Of IPv6
http://www.networkcomputing.com/ipv6/six-benefits-of-ipv6/230500009


New 200-105 exam questions from PassLeader 200-105 dumps! Welcome to download the newest PassLeader 200-105 VCE and PDF dumps: http://www.passleader.com/200-105.html (346 Q&As)

P.S. Free 200-105 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpUTVNc3otMV8xMkU