web analytics

Cisco CCNA Industrial 200-601 Dumps With VCE and PDF Download (Question 1 – Question 5)

New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ

QUESTION 1
Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection and sets the priority value that would break the tie between switches with matching default criteria to 50?

A.    ptp mode boundary
ptp priority1 10
ptp priority2 50
B.    ptp mode boundary
ptp priority1 50
ptp priority2 10
C.    ptp mode e2etransparent
ptp priority1 50
ptp priority2 10
D.    ptp mode e2etransparent
ptp priority1 10
ptp priority2 50

Answer: A

QUESTION 2
What are three Cisco best practices for running I/O control traffic in a wireless environment? (Choose three.)

A.    3200 packets per second and 20% bandwidth for HMI and maintenance traffic
B.    2200 packets per second and 20% bandwidth for HMI and maintenance traffic
C.    I/O control traffic can be run on 2.4 or 5 GHZ channels
D.    I/O control traffic should be run on 5GHZ channels only
E.    Standard I/O RPIs less than 20ms are not practical for wireless media because the maximum latency and jitter become comparable or greater than the RPI
F.    Standard I/O RPIs less than 10ms are not practical for wireless media because the maximum latency and jitter become comparable or greater than the RPI

Answer: BDF

QUESTION 3
If the Link Fault alarm is connected to the minor relay and the FCS Bit Error Rate alarm is connected to the major relay, which commands will create an alarm profile called GigE with the alarms correctly mapped to the minor and major relays?

A.    Switch(config)#alarm profile GigE
Switch(config-alarm-prof)#alarm 1 4
Switch(config-alarm-prof)#relay major 4
Switch(config-alarm-prof)#relay minor 1
B.    Switch(config)#alarm profile GigE
Switch(config-alarm-prof)#alarm 1 3
Switch(config-alarm-prof)#relay major 3
Switch(config-alarm-prof)#relay minor 1
C.    Switch(config)#alarm profile GigE
Switch(config-alarm-prof)#alarm 1 3
Switch(config-alarm-prof)#relay major 1
Switch(config-alarm-prof)#relay minor 3
D.    Switch(config)#alarm profile GigE
Switch(config-alarm-prof)#alarm 1 4
Switch(config-alarm-prof)#relay major 1
Switch(config-alarm-prof)#relay minor 4

Answer: A

QUESTION 4
Refer to the exhibit. Network Faceplates have not been installed on the HMI and so you need to map a network based on information available from RSLinx. Which most accurately represents the network configuration?
 

A.    Missing
B.    Missing
C.    Missing
D.    Missing

Answer: B

QUESTION 5
Refer to the exhibit. Which lines represent an I/O connection running at a 20ms RPI?
 

A.    2919, 2923, 2926
B.    2920, 2926, 2929
C.    2922, 2929, 2935
D.    2914, 2915, 2916

Answer: A


New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ