This page was exported from PassLeader New Cisco Exam Dumps Collection [ ] Export date:Thu Jan 17 2:36:05 2019 / +0000 GMT ___________________________________________________ Title: PassLeader Valid 300-115 Dumps with VCE and PDF (Question 91 - Question 100) --------------------------------------------------- New 300-115 exam questions from PassLeader 300-115 dumps! Welcome to download the newest PassLeader 300-115 VCE and PDF dumps: (808 Q&As --> 867 Q&As --> 971 Q&As --> 1042 Q&As) P.S. Free 300-115 dumps are available on Google Drive shared by PassLeader: QUESTION 91 What is the default amount by which the hot standby priority for the router is decremented or incremented when the interface goes down or comes back up? A.    1 B.    5 C.    10 D.    15 Answer: C QUESTION 92 What is the maximum number of virtual MAC addresses that GLBP allows per group? A.    2 B.    4 C.    6 D.    8 Answer: B QUESTION 93 Which gateway role is responsible for answering ARP requests for the virtual IP address in GLBP? A.    active virtual forwarder B.    active virtual router C.    active virtual gateway D.    designated router Answer: C QUESTION 94 Which VRRP router is responsible for forwarding packets that are sent to the IP addresses of the virtual router? A.    virtual router master B.    virtual router backup C.    virtual router active D.    virtual router standby Answer: A QUESTION 95 Which command correctly configures standby tracking for group 1 using the default decrement priority value? A.    standby 1 track 100 B.    standby 1 track 100 decrement 1 C.    standby 1 track 100 decrement 5 D.    standby 1 track 100 decrement 20 Answer: A QUESTION 96 Which command configures an HSRP group to become a slave of another HSRP group? A.    standby slave B.    standby group track C.    standby follow D.    standby group backup Answer: C QUESTION 97 Refer to the exhibit. Which option describes the reason for this message in a GLBP configuration? A.    Unavailable GLBP active forwarder B.    Incorrect GLBP IP address C.    HSRP configured on same interface as GLBP D.    Layer 2 loop Answer: D QUESTION 98 Lab Simulation - LACP with STP Sim You work for They have just added a new switch (SwitchB) to the existing network as shown in the topology diagram. RouterA is currently configured correctly and is providing the routing function for devices on SwitchA and SwitchB. SwitchA is currently configured correctly, but will need to be modified to support the addition of SwitchB. SwitchB has a minimal configuration. You have been tasked with competing the needed configuring of SwitchA and SwitchB. SwitchA and SwitchB use Cisco as the enable password. Configuration Requirements for SwitchA The VTP and STP configuration modes on SwitchA should not be modified. - SwitchA needs to be the root switch for vlans 11, 12, 13, 21, 22 and 23. All other vlans should be left are their default values. Configuration Requirements for SwitchB - Vlan 21 Name: Marketing will support two servers attached to fa0/9 and fa0/10 - Vlan 22 Name: Sales will support two servers attached to fa0/13 and fa0/14 - Vlan 23 Name: Engineering will support two servers attached to fa0/15 and fa0/16 - Access ports that connect to server should transition immediately to forwarding state upon detecting the connection of a device. - SwitchB VTP mode needs to be the same as SwitchA. - SwitchB must operate in the same spanning tree mode as SwitchA - No routing is to be configured on SwitchB - Only the SVI vlan 1 is to be configured and it is to use address Inter-switch Connectivity Configuration Requirements - For operational and security reasons trunking should be unconditional and Vlans 1, 21, 22 and 23 should tagged when traversing the trunk link. - The two trunks between SwitchA and SwitchB need to be configured in a mode that allows for the maximum use of their bandwidth for all vlans. This mode should be done with a non-proprietary protocol, with SwitchA controlling activation. - Propagation of unnecessary broadcasts should be limited using manual pruning on this trunk link. Answer: SW-A (close to router) SW-A#configure terminal SW-A(config)#spanning-tree vlan 11-13,21-23 root primary SW-A(config)#vlan 21 SW-A(config-vlan)#name Marketing SW-A(config-vlan)#exit SW-A(config)#vlan 22 SW-A(config-vlan)#name Sales SW-A(config-vlan)#exit SW-A(config)#vlan 23 SW-A(config-vlan)#name Engineering SW-A(config-vlan)#exit SW-A(config)#interface range Fa0/3 – 4 SW-A(config-if-range)#no switchport mode access SW-A(config-if-range)#no switchport access vlan 98 (These two commands must be deleted to form a trunking link) SW-A(config-if-range)#switchport trunk encapsulation dot1q (cannot issued this command on this switch, but don‘t worry coz I still got 100%) SW-A(config-if-range)#switchport mode trunk SW-A(config-if-range)#switchport trunk native vlan 99 SW-A(config-if-range)#switchport trunk allowed vlan 1,21-23 SW-A(config-if-range)#channel-group 1 mode active SW-A(config-if-range)#channel-protocol lacp SW-A(config-if-range)#no shutdown SW-A(config-if-range)#end SW-B (far from router) SW-B#configure terminal SW-B(config)#vlan 21 SW-B(config-vlan)#name Marketing SW-B(config-vlan)#exit SW-B(config)#vlan 22 SW-B(config-vlan)#name Sales SW-B(config-vlan)#exit SW-B(config)#vlan 23 SW-B(config-vlan)#name Engineering SW-B(config-vlan)#exit SW-B(config)#vlan 99 SW-B(config-vlan)#name TrunkNative // not necessary to name it but just name it same as SwitchA SW-B(config-vlan)#exit SW-B(config)#interface range Fa0/9 – 10 SW-B(config-if-range)#switchport mode access SW-B(config-if-range)#switchport access vlan 21 SW-B(config-if-range)#spanning-tree portfast SW-B(config-if-range)#no shutdown SW-B(config-if-range)#exit SW-B(config)#interface range Fa0/13 – 14 SW-B(config-if-range)#switchport mode access SW-B(config-if-range)#switchport access vlan 22 SW-B(config-if-range)#spanning-tree portfast SW-B(config-if-range)#no shutdown SW-B(config-if-range)#exit SW-B(config)#interface range Fa0/15 – 16 SW-B(config-if-range)#switchport mode access SW-B(config-if-range)#switchport access vlan 23 SW-B(config-if-range)#spanning-tree portfast SW-B(config-if-range)#no shutdown SW-B(config-if-range)#exit SW-B(config)#vtp mode transparent SW-B(config)#spanning-tree mode rapid-pvst SW-B(config)#ip default-gateway (you can get this IP from SW-A with command show cdp neighbour detail) // not sure about this command because the question says “No routing is to be configured on SwitchB”. SW-B(config)#interface vlan 1 SW-B(config-if)#ip address SW-B(config-if)#no shutdown SW-B(config-if)#exit SW-B(config)#interface range Fa0/3 – 4 SW-B(config-if-range)#switchport trunk encapsulation dot1q (yes I can issued this command on this switch) SW-B(config-if-range)#switchport mode trunk SW-B(config-if-range)#switchport trunk native vlan 99 SW-B(config-if-range)#switchport trunk allowed vlan 1,21-23 SW-B(config-if-range)#channel-group 1 mode passive //mode passive because “SwitchA controlling activation” SW-B(config-if-range)#channel-protocol lacp SW-B(config-if-range)#no shutdown SW-B(config-if-range)#end Some guidelines for configuring SwitchA & SwitchB: You may have to configure Interface Port-Channel on both switches. Check the configuration first, if it does not exist, use these commands: interface port-channel1 switchport mode trunk switchport trunk native vlan 99 //this command will prevent the “Native VLAN mismatched” error on both switches switchport trunk allowed vlan 1,21-23,99 Some notes for this sim: + You should check the initial status of both switches with these commands: show vtp status (transparent mode on switchA and we have to set the same mode on switchB), show spanning-tree [summary] (rapid-pvst mode on switchA and we have to set the same mode on switchB), show vlan (check the native vlan and the existence of vlan99), show etherchannel 1 port-channel and show ip int brief (check if Port-channel 1 has been created and make sure it is up), show run (to check everything again). + When using "int range f0/x - y" command hit space bar before and after "-" otherwise the simulator does not accept it. + You must create vlan 99 for the switchB. SwitchA already have vlan 99 configured. + At the end, you can try to ping from SwitchB to RouterA (you can get the IP on RouterA via the show cdp neighbors detail on SwitchA), not sure if it can ping or not. If not, you can use the "ip default-gateway" on SwitchB. + The name of SwitchA and SwitchB can be swapped or changed so be careful to put your configuration into appropriate switch. QUESTION 99 Lab Simulation - AAAdot1x is an IT company that has an existing enterprise network comprised of two layer 2 only switches; DSW1 and ASW1. The topology diagram indicates their layer 2 mapping. VLAN 20 is a new VLAN that will be used to provide the shipping personnel access to the server. Corporate polices do not allow layer 3 functionality to be enabled on the switches. For security reasons, it is necessary to restrict access to VLAN 20 in the following manner: - Users connecting to VLAN 20 via portfO/1 on ASW1 must be authenticated before they are given access to the network. Authentication is to be done via a Radius server: - Radius server host: - Radius key: rad123 - Authentication should be implemented as close to the host as possible. - Devices on VLAN 20 are restricted to the subnet of - Packets from devices in the subnet of should be allowed on VLAN 20. - Packets from devices in any other address range should be dropped on VLAN 20. - Filtering should be implemented as close to the serverfarm as possible. The Radius server and application servers will be installed at a future date. You have been tasked with implementing the above access control as a pre-condition to installing the servers. You must use the available IOS switch features. Answer: 1. Verification of Pre-configuration: a. Check that the denoted vlan [vlan20] is created in both switches and ports [fa0/1 of ASW1] are assigned. b. Take down the radius-server ip [] and the key [rad123]. c. Take down the IP range [] to be allowed the given vlan [vlan20] 2. Configure the Port based authentication on ASW1: Enable AAA on the switch: ASW1(config)# aaa new-model The new-model keyword refers to the use of method lists, by which authentication methods and sources can be grouped or organized. Define the server along with its secret shared password: ASW1(config)# radius-server host key rad123 ASW1(config)# aaa authentication dot1x default group radius This command causes the RADIUS server defined on the switch to be used for 802.1x authentication. Enable 802.1x on the switch: ASW1(config)# dot1x system-auth-control Configure Fa0/1 to use 802.1x: ASW1(config)# interface fastEthernet 0/1 ASW1(config-if)# switchport mode access ASW1(config-if)# dot1x port-control auto Notice that the word “auto” will force connected PC to authenticate through the 802.1x exchange. ASW1(config-if)# exit ASW1# copy running-config startup-config 3. Filter the traffic and create vlan access-map to restrict the traffic only for a range on DSW1 Define an access-list: DSW1(config)# ip access-list standard 10 (syntax: ip access-list {standard | extended} acl-name) DSW1(config-ext-nacl)# permit DSW1(config-ext-nacl)# exit Define an access-map which uses the access-list above: DSW1(config)# vlan access-map MYACCMAP 10 (syntax: vlan access-map map_name [0-65535] ) DSW1(config-access-map)# match ip address 10 (syntax: match ip address {acl_number | acl_name}) DSW1(config-access-map)# action forward DSW1(config-access-map)# exit DSW1(config)# vlan access-map MYACCMAP 20 DSW1(config-access-map)# action drop (drop other networks) DSW1(config-access-map)# exit Apply a vlan-map into a vlan: DSW1(config)# vlan filter MYACCMAP vlan-list 20 (syntax: vlan filter mapname vlan-list list) DSW1# copy running-config startup-config 4. Note: It is not possible to verify the configuration in this lab. All we have do the correct configurations. Most of the exam takers report that "copy running-config startup-config" is not working. It does not a matter. Do not try unwanted/wrong commands in the consoles. They are not real switches. QUESTION 100 Hotspot - HSRP Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution. - DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105 - DSW2 - primary device for VLAN 103 and VLAN 104 - A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed. Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question. During routine maintenance, GigabitEthernet1/0/1 on DSW1 was shut down. All other interfaces were up. DSW2 became the active HSRP device for VLAN 101 as desired. However, after GigabitEthemet1/0/1 on DSW1 was reactivated, DSW1 did not become the active router for VLAN 101 as desired. What needs to be done to make the group for VLAN 101 function properly? A.    Enable preempt in the VLAN 101 HSRP group on DSW1. B.    Disable preempt in the VLAN 101 HSRP group on DSW2. C.    In the VLAN 101 HSRP group on DSW1, decrease the priority value to avaluethatis less ' than the priority value configured in the VLAN 101 HSRP group on DSW2. D.    Decrease the decrement value in the track command for the VLAN 101 HSRP group on U DSWTs to a values less than the value in the track command for the VLAN 101 HSRP group on DSW2. Answer: A New 300-115 exam questions from PassLeader 300-115 dumps! Welcome to download the newest PassLeader 300-115 VCE and PDF dumps: (808 Q&As --> 867 Q&As --> 971 Q&As --> 1042 Q&As) P.S. Free 300-115 dumps are available on Google Drive shared by PassLeader: --------------------------------------------------- Images: --------------------------------------------------- --------------------------------------------------- Post date: 2016-11-01 10:52:07 Post date GMT: 2016-11-01 10:52:07 Post modified date: 2019-01-16 08:42:11 Post modified date GMT: 2019-01-16 08:42:11 ____________________________________________________________________________________________ Export of Post and Page as text file has been powered by [ Universal Post Manager ] plugin from